This is the first of a short series of articles on how to use Sonic Pi for sound design. We’ll be take a quick tour of a number of different techniques available for you to craft your own unique sound.
The first technique we’ll look at is called additive synthesis. This may sound complicated - but if we expand each word slightly, the meaning pops right out. Firstly, ‘additive’ means a combination of things; secondly, ‘synthesis’ means to combine thing, in this case sounds. Additive synthesis therefore means nothing more complicated than combining existing sounds to create new ones.
The full article can be found in The MagPi 54 and was written by Sam Aaron.
This synthesis technique dates back a very long time – for example, pipe organs in the Middle Ages had lots of slightly different-sounding pipes which you could enable or disable with stops. Pulling out the stop for a given pipe ‘added it to the mix’, making the sound richer and more complex. Now, let’s see how we can pull out all the stops with Sonic Pi.
Let’s start with the most basic sound there is – the humble pure-toned sine wave:
synth :sine, note: :d3
Now, let’s see how this sounds combined with a square wave:
synth :sine, note: :d3 synth :square, note: :d3
Notice how the two sounds combine to form a new, richer sound. Of course, we don’t have to stop there: we can add as many sounds as we need. However, we need to be careful with how many sounds we add together. Just like when we mix paints to create new colours, adding too many colours will result in a messy brown. Similarly, adding too many sounds together will result in a muddy sound.
Let’s add something to make it sound a little brighter. We could use a triangle wave at an octave higher (for that high bright sound), yet only play it at amp 0.4 so it adds something extra to the sound rather than taking it over:
synth :sine, note: :d3 synth :square, note: :d3 synth :tri, note: :d4, amp: 0.4
Now, you can try creating your own sounds by combining two or more synths at different octaves and amplitudes. Also, note that you can play around with a synth’s opts to modify each source sound before it is mixed in for even more combinations of sounds.
So far, when combining our different synths we’ve used either the same pitch or switched octave. How might it sound if we didn’t stick to octaves but instead chose a slightly higher or lower note? Let’s try it:
detune = 0.7 synth :square, note: :e3 synth :square, note: :e3 + detune
If we detune our square waves by 0.7 notes, we hear something that perhaps doesn’t sound in tune or correct – a ‘bad’ note. However, as we move closer to 0, it will sound less and less out of tune as the pitch of two waves gets closer and more similar. Try it for yourself! Change the detune: opt value from 0.7 to 0.5 and listen to the new sound. Try 0.2, 0.1, 0.05, 0. Each time you change the value, take a listen and see if you can hear how the sound is changing. Notice that low detune values such as 0.1 produce a really nice ‘thick’ sound, with both slightly different pitches interacting with each other in interesting, often surprising, ways.
Some of the built-in synths already include a detune option that do exactly this in one synth. Try playing with the detune: opt of :dsaw, :dpulse, and :dtri.
Another way in which we can finely craft our sound is to use a different envelope and options for each synth trigger. For example, this will allow you to make some aspects of the sound percussive and other aspects ring out for a period of time.
detune = 0.1 synth :square, note: :e1, release: 2 synth :square, note: :e1 + detune, amp: 2, release: 2 synth :gnoise, release: 2, amp: 1, cutoff: 60 synth :gnoise, release: 0.5, amp: 1, cutoff: 100 synth :noise, release: 0.2, amp: 1, cutoff: 90
In the example above, we have mixed in a noisy percussive element to the sound along with some more persistent background rumbling. This was achieved firstly by using two noise synths with middling cutoff values (90 and 100), using short release times, along with a noise with a longer release time but with a low cutoff value (which makes the noise less crisp and more rumbly.)
Bringing it all together
Let’s combine all these techniques to see if we can use additive synthesis to recreate a basic bell sound. We’ve broken this example into four sections. Firstly we have the ‘hit’ section, which is the initial onset part of the bell sound, and so uses a short envelope (e.g. a release: of around 0.1). Next we have the long ringing section, for which we’re using the pure sound of the sine wave. Notice that we’re often increasing the note by roughly 12 and 24, which is the number of notes in an octave. We’ve also thrown in a couple of low sine waves to give the sound some bass and depth. Finally, we use define to wrap our code in a function which we can then use to play a melody. Try playing your own melody and also messing around with the contents of the :bell function until you create your own crazy sound to play with!
define :bell do |n| # Triangle waves for the ‘hit’ synth :tri, note: n - 12, release: 0.1 synth :tri, note: n + 0.1, release: 0.1 synth :tri, note: n - 0.1, release: 0.1 synth :tri, note: n, release: 0.2 # Sine waves for the ‘ringing’ synth :sine, note: n + 24, release: 2 synth :sine, note: n + 24.1, release: 2 synth :sine, note: n + 24.2, release: 0.5 synth :sine, note: n + 11.8, release: 2 synth :sine, note: n, release: 2 # Low sine waves for the bass synth :sine, note: n - 11.8, release: 2 synth :sine, note: n - 12, release: 2 end # Play a melody with our new bell! bell :e3 sleep 1 bell :c2 sleep 1 bell :d3 sleep 1 bell :g2