50 Raspberry Pi 4 Tips and Tools: pt 2

By Mark Vanstone. Posted

Whether you're assembling a project from a kit or designing and prototyping a brand new Raspberry Pi-based 'thing', you won't get far without the necessary tools to complete it. In part II of our resource list we present 25 more tools and accessories you should have to hand when embarking on Raspberry Pi (or other) projects in your maker space.

For part I of this guide to tools every maker should have, see here.


Some of these tools use mains electricity and heated parts. Always follow connection instructions and never leave heated elements unattended.

Cutting, trimming and coverings

26. Card trimmer

A card trimmer will enable you to cut crisp straight lines in paper or thin card. It’s much quicker than a ruler and craft knife. Small ones are good for trimming photos, and a good-quality trimmer will last for years.

27. Robotic craft cutter

A robotic craft cutter is very much like a plotter, but has a knife instead of a pen. They can cut very intricate designs out of paper and fairly thick card. They can be a bit temperamental and often need a sticky carrier sheet to work well.

Equipped with a knife for precision cutting, a robotic craft cutter can cut intricate designs out of paper or card

28. Laser cutter or engraver

Laser cutters and engravers fire a laser at a material to either cut through it or to leave a mark or indent on the surface, depending on the intensity of the laser. Very effective for cutting irregular wooden shapes.

29. Laminator

Lamination is the process of coating a material with a plastic film. This protects the material from moisture and other damage. It also makes the material thicker. Plastic laminate comes in various thicknesses and surface finishes.

Laminate your prototype model to protect it from moisture and general wear and tear

30. Conductive paint

Generally coloured black and supplied in a tube, conductive paint can be used to draw electrical circuits on paper or card, or to improve poor connections between components and even to create touch-sensitive areas on materials. Dries in a few minutes.

Use conductive paint to draw electrical circuits or to improve connections between components

31. Acrylic and thermoplastic sheet

Acrylic plastic sheeting is very tough and can be cut using a saw or CNC router, whereas thermoplastic sheets are malleable when heated with a heat gun. Once cool again, thermoplastic retains its new shape.

32. Polymorphic plastic

This material is usually supplied as granules or beads. You can heat them up in boiling water and they will clump together in a mass. While still warm, you can mould the plastic before it sets hard in ten minutes or so.

Polymorphic plastic beads can be moulded or shaped anyway you like and, once wet, will set hard in 10 minutes

33. Aluminium foil

Available from convenience stores and supermarkets, aluminium foil can be used as a conductor in a circuit, as shielding to reduce electromagnetic interference, and also to reflect light and heat either away from or towards an area.

Tools for connecting electronics

34. GPIO ruler/chart

GPIO (general-purpose input/output) pins are the interface between your Raspberry Pi and electronic components. Until you learn which pin is which, you’ll need a guide. There are several GPIO rulers and guides available to make life easier.

A GPIO ruler provides a handy reference guide to which coloured pin does what

35. Header connector

For some projects, you may want to connect a HAT or pHAT to your Raspberry Pi, but not place it right on top of the board. In this case, a female-to-male 40-way ribbon connector enables you to extend the reach of the GPIO pins.

36. Jumper wires

Jumper wires connect Raspberry Pi GPIO pins to electronic components. Use them with a breadboard to prototype your circuit, or solder them directly to components. Be sure to get a variety of different colours to make your project easier to understand.

Jumper wires connect components on a breadboard or can be soldered directly to it

Tools for soldering

37. Desoldering kit

This equipment enables you to clean melted solder from components on a printed circuit board, allowing their removal or replacement.

If you're doing anything with electronics, a soldering kit is pretty much essential

38. Soldering station

A handy stand to place a soldering iron while it is still plugged in and hot. The sponge should be wet to clean the end of the iron.

39. Soldering iron

An absolute necessity for soldering or desoldering components onto printed circuit boards. For detailed work, an iron with a pointed end is best.

40. Third hand tool

Usually has a solid, heavy base with jointed arms with clips or holders at the end, and a magnifying glass for working on small components.

41. Multimeter

You need to be able to measure current, resistance, and voltage in your circuits. Digital multimeters can cost as little as £10.

Measure voltage, resistance and current using a multimeter

42. Gorilla Glue

Similar to superglue, but supplied with a brush to apply it, Gorilla Glue sticks most materials and very good for 3D-printed parts. Usually takes around half an hour to dry.

Ideal for sticking together 3D parts - or almost anything else - Gorilla Glue is easier to apply than superglue because it comes with an applicator brush

43. Nuts, bolts & screws

Having a good range of sizes and shapes of nuts, bolts, and screws is absolutely necessary for making anything that you are not going to glue. Keep a jar full of spares.

We recommend you have an abundant supply of nuts, bolts and screws

44. Sticky tape

For temporarily holding things in place or insulating wires. You can also use tape for wrapping handles of tools. Also good for removing cat fur from jumpers.

Sticky tape is great for quick fixes and adding grip to tool handles

45. Blu Tack

Usually used for keeping posters on walls, but can also be used for holding components in place while soldering. It also rubs out pencil marks if you don’t have an eraser.

46. Power bank/batteries

Most maker projects need power, so it is a good idea to have a range of battery holders. Power banks for recharging phones can also be used for 5V supplies.

Many maker projects depend on a steady supply of batteries

47. 3D creation software

You may want to visualise your build before starting, and there are many 3D software packages to help you for free, like Blender; or with free trial versions, such as SketchUp.

3D creation software such as Blender and SketchUp help you visualise and plan your project

48. Fritzing

When you have completed your project, you may want to document how you did it. Fritzing is a great program for laying out circuit diagrams.

Use Fritzing to document your completed project

49. Paper clips

Can be used to connect components, clean out small nooks and crannies, or hold materials in place. Apparently, you can pick locks with them too!

50. Documentation

One of the most important tools you will use for just about any maker project is reference material. Your Raspberry Pi may have come with some tips and hints about making, and many kits have worksheets and Frequently Asked Questions sections with them.

Also, make best use of the online resources that detail other people’s experiences: like Stack Overflow for information about any technical subject; blogs such as modmypi.com, recantha.co.uk, and blog.pimoroni.com; and of course the Raspberry Pi site and magazines. If you’re stuck getting something to work, it’s likely someone else has had the same problem!

Get advice and how-to guides from invaluable online sites and component maker's blogs

From The MagPi store